青州温室水培灌溉设备LI-76喷灌机

喷灌机的特点
1、喷头：采用进口三位、快速转换、防滴漏、水雾化喷头，只要轻轻旋转就可以实现喷水量的改变。
2、专利防滴：喷嘴设有专利防滴装置，开启压力为1Kgf/cm2。这对于育苗灌溉意义重大。
稳速运行：实时监测并修正运行速度，闭环控制保证匀速，真正实现均匀灌溉。
3、分块施水：选择性设置左右喷水开关功能。实现道路或闲置区域关闭喷水之功能。
4、行程设置：只要移动起点、终点开关挡板，就可以改变机器喷灌面积。
5、自动运行：设置开停机时间，机器完全可以在您的设定时间段自动执行灌溉作业。
6、手动操作或遥控操作。全自动往复运行。
7、喷杆高度：可以方便地调整，调整范围约500 mm。保证作物长高仍能得到均匀灌溉。
8、节约土地：吊挂式安装zui大限度地节约了宝贵的种植面积。同时双轨使机器运行平稳。
9、可以接受计算机控制系统信号指令，实现远程控制。
10、可以输出对于供水泵的开关控制信号，实现停止喷水的同时停止水泵供水，节省水源。
喷灌机选用原则
一般建议每栋温室配置一台机器，以避免转移轨道必须人工推行的不便或麻烦。
喷灌机的zui大行程是80米。
工作轨道的长度通常就是温室长度，也就是喷灌机作业行程；工作轨道一般要求安装成水平；苗床或地面上种植作物和喷嘴之间的距离以不小于450 mm为宜；工作轨道的高度一般在2000mm-2200mm之间。
在每一栋温室的端部预留出水源和电源接口。水源接口尺寸为DN20外径的UPVC管，要求水压力不小于3 Kgf/cm2。电源为~220V/50Hz。
由于喷灌机机身长度和胶管滑车长度，在机器进水端总有1.5米，行程终端约有0.5米不能喷到。
如果一台机器用于多栋温室，则一般不建议超过三连栋。此时则必须在栋与栋之间设置转移车用的转移轨道。注：喷灌机转移工作，需要人工推行完成。转移轨道下方必须设置道路，便于操作使用喷灌机、接水接电。
Selection principle of sprinkler irrigation machine
It is generally recommended that each greenhouse be equipped with a machine to avoid the inconvenience or trouble of manual operation of transfer track.
The Zui large stroke of sprinkler irrigation machine is 80 meters.
The length of the working track is usually the length of the greenhouse, that is, the operation stroke of the sprinkler irrigation machine; the working track is generally required to be instalLED horizontally; the distance between the crops planted on the seedbed or ground and the nozzle should not be less than 450 mm; the height of the working track is generally between 2000mm and 2200mm.
Water source and power interface are reserved at the end of each greenhouse. For the UPVC pipe with DN20 outer diameter, the water pressure is required to be no less than 3 kgf / cm2. The power supply is ~ 220 V / 50 Hz.
Due to the length of the machine body and the length of the hose pulley, there is always 1.5 m at the water inlet end of the machine, and about 0.5 m at the end of the stroke.
If one machine is used for more than one greenhouse, it is generally not recommended to have more than three greenhouses. At this time, transfer tracks for transfer vehicles must be set between buildings. Note: the transfer of sprinkler irrigation machine needs to be carried out manually.
The road must be set under the transfer track to facilitate the operation and use of sprinkler irrigation machine, water and electricity.